Long Range 3KM 5.8G 300Mbps Outdoor Router Point To Point Wireless Wifi Bridge
Product Description
Cpe028 is an outdoor high-performance 300 Mbps 5.8G CPE with an operating frequency of 5g. It supports point-to-point and point to multipoint wireless connections. It has better anti-interference performance than 2.4G products. It can be managed through the web interface.
Characteristic
1. Comply with 5.8GHz IEEE 802.11a and IEEE 802.11n standards
2. Support CSMA / Ca, CSMA / CD, TCP / IP, PPPoE, DHCP, ICMP and NAT protocols
3. Transmission distance: 5km (visible unobstructed environment)
4. Low interference: at present, most wireless devices work at 2.4G frequency, and 5g frequency makes them have better anti-interference performance
5. The transmission speed is up to 300 Mbps, and the built-in 14 DBI directional antenna can significantly improve the transmission and reception performance of wireless signals
6. Support Poe power supply (50m), easy installation and cost saving
7. Support 64 / 128 bit WEP encryption and WPA - PSK, WPA 2 - PSK security protection
8. Good compatibility and strong anti-interference ability of adjacent channels; It can automatically adjust to the best transmission speed according to the actual signal strength and transmission distance.
Specification
| Outdoor CPE | ||||
| Item | Specifications | |||
| Solution | CPU:AR9344 RF:AR9344 | |||
| Standards |
IEEE802.3u MDI/MDIX 10/100Mbps IEEE802.11a IEEE 802.11n |
|||
| DDR | 64Mbyte | |||
| FLASH | 8Mbyte | |||
| PoE Power | 12V—24V passive POE support | |||
| CPU Frequency | 533MHz | |||
| Antenna | Internal 14dBi directional panel dual-polarization antenna (horizontal beam 60º, Vertical beam 25º) | |||
| Antenna | 2×2 (2Tx,2 Rx) | |||
| Physical Ports | 2 10/100Mbps Ports | |||
| Reset Button | Restore factory settings | |||
| Firmware Upgrade | Through Web and TFTP | |||
| LED |
Power LED l On :The power is on/system starts l Off: The power is off/system closes Lan LED l Off:There is no other device connected to the port l On:There is other device connected to the port l Blinking:There is data transmission on the port Wireless LED(AP Mode) l Off:No wireless connection l Blinking:There is wireless data transmission Wireless Signal Strength LED(Client mode) l Four signal strength indication LED all lighting up means the signal strength is at highest level; l Four signal strength indication LED all blinking means the signal strength is at weakest level |
|||
| Power Supply | 12VDC 1.5A or 18VDC 1A | |||
| Data Transfer Rate |
11a: 54M, 48M, 36M, 24M, 18M, 12M, 9M, 6Mbps HT20:7.2M,14.4M,21.7M,28.9M,43.3M,57.8M,65M,72.2M,14.4M,28.9M, 43.3M,57.8M,86.7M,115.6M,130M,144.4M HT40:15M,30M,45M,60M,90M,120M,135M,150M,30M,60M,90M,120M, 180M,240M,270M,300M |
|||
| Transmission Type | DSSS | |||
| Modulation Type | OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK | |||
| RF Frequency range | 5.725 GHz ~ 5.850 GHz (channel 149 ~ 165) | |||
| RF Power | 802.11a | 6-24Mbps | 24.0 ± 2.0dBm | |
| 36-48Mbps | 23.0 ± 2.0dBm | |||
| 54Mbps | 22.0± 2.0dBm | |||
| 802.11n | HT20 | MCS 0-3 | 23.0 ± 2.0dBm | |
| MCS 4 | 22.5 ± 2.0dBm | |||
| MCS 5 | 21.5 ± 2.0dBm | |||
| MCS 6 | 21.0 ± 2.0dBm | |||
| MCS 7 | 20.0 ± 2.0dBm | |||
| HT40 | MCS 0-3 | 23.0 ± 2.0dBm | ||
| MCS 4 | 22.5 ± 2.0dBm | |||
| MCS 5 | 21.5 ± 2.0dBm | |||
| MCS 6 | 21.0 ± 2.0dBm | |||
| MCS 7 | 20.0 ± 2.0dBm | |||
| Sensitivity |
IEEE 802.11a 6Mbps= -90dBm 54Mbps =-71dBm |
IEEE 802.11n HT 20 MCS 0=- 86dBm MCS 7=- 68dBm HT 40 MCS 0=- 83dBm MCS 7=- 65dBm |
||
| Power consumption | 8W Max | |||
| Environment | ||||
| Operation Temperature | -20~+70°C | |||
| Operation Humidity(non-condensation) | 10%~95% RH | |||
| Store Temperature | -40~+85°C | |||
| Store Humidity(non-condensation) | 10%~95% RH | |||
| Environmental Standards | RoHs Compliance | |||
Detailed image
FAQ
Q1. Can I have a sample order?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.
Q2. What about the lead time?
A: Sample needs 1-3 working days, mass production time needs 3-5 weeks based on order quantity.
Q3. Do you have any MOQ limit?
A: Low MOQ, 1pc for sample checking is available.
Q4. Do your products meet our standards?
A: Yes, almost all our products have CE,ROHS,FCC,etc.
Q5. How to proceed an order?
A: Firstly let us know your requirements or application. Secondly We quote according to your requirements or our suggestions.Thirdly customer confirms the samples and places deposit for formal order. Then we arrange the production.
Our products are sold all over the world, you can rest assured.
